Suitable medium
Pumps for Sodium chloride, 20%, 40 °C
36 FLUX pumps are suitable for Sodium chloride, 20%, 40 °C. Compare them below by type, material, flow rate and head.
- Concentration
- 20%
- Temperature
- 40 °C
Suitable pumps
F 400 - for low viscosity media-from drums or IBCs
F 430 AL-41/38
for pumping petroleum products out of drums.
- Motor type:
- FEM 4070
- Max. flow rate:
- 65 l/min
- Max. discharge head:
- 9.5 mWk
- Rated output:
- 0.5 kW
F 400 - for low viscosity media-from drums or IBCs
F 424 PP/S-41/35Z
for filling Adblue® from IBCs.
- Motor type:
- FEM 4070
- Rated output:
- 0.5 kW
- Supply voltage:
- 230-240 V
- Material:
- Polypropylene
F 400 - for low viscosity media-from drums or IBCs
F 424 PP/S-41/35Z
for filling Adblue® from IBCs.
- Motor type:
- FEM 4070
- Max. flow rate:
- 50 l/min
- Max. discharge head:
- 18 mWk
- Rated output:
- 0.5 kW
F 400 - for low viscosity media-from drums or IBCs
F 430 PVDF-40/33
for pumping concentrated acids out of drums.
- Motor type:
- F 458
- Max. flow rate:
- 40 l/min
- Max. discharge head:
- 9.5 mWk
- Rated output:
- 0.46 kW
F 300 - for small filling quantities
FP 314 PP/S-32/25
for small AdBlue® fill quantities, with removable battery-powered motor.
- Motor type:
- FBM-B 3100 (brushless)
- Max. flow rate:
- 33 l/min
- Max. discharge head:
- 6.5 mWk
- Rated output:
- 0.1 kW
F 300 - for small filling quantities
F 314 PP/S-32/25
for small AdBlue® fill quantities, with a permanently attached motor.
- Motor type:
- F 310
- Max. flow rate:
- 36 l/min
- Max. discharge head:
- 6.7 mWk
- Rated output:
- 0.23 kW
Drum and container pumps
F 430 AL-41/38 | NBR
with mechanical seal, for pumping out of drums. Made from aluminium, NBR seal.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Aluminium
Drum and container pumps
F 430 AL-50/38 | NBR
with mechanical seal, for pumping out of drums. Made from aluminium, NBR seal, 50 mm diameter.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Aluminium
Drum and container pumps
F 430 AL-41/37 Z | NBR
with mechanical seal, for pumping out of drums. Made from aluminium, NBR seal, semi-axial rotor.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 30 mWk
- Material:
- Aluminium
Drum and container pumps
F 430 PP-40/33 TR | FKM
for horizontal use (dry well installation), made from polypropylene, FKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 424 PP-41/36 | FKM
sealless, for pumping out of drums. Made from polypropylene, FKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PP-40/33 | FKM
with mechanical seal, for pumping out of drums. Made from polypropylene, FKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 424 PP-41/35 Z | FKM
sealless, for pumping out of drums. Made from polypropylene, FKM seal, semi-axial rotor.
- Max. flow rate:
- 100 l/min
- Max. discharge head:
- 24 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PP-50/43 Z | FKM
with mechanical seal, for pumping out of drums. Made from polypropylene, FKM seal, semi-axial rotor.
- Max. flow rate:
- 110 l/min
- Max. discharge head:
- 30 mWk
- Material:
- Polypropylene
Flow Meter
FMC 100/S/PPS/2/A | FKM
Nutating disc flowmeter, for use with drum pumps, made from PPS, FKM seal.
- Material:
- Stainless steel
Flow Meter
FMO 110/S/S/1
Oval gear flowmeter, for use with drum pumps, stainless steel, up to 1,000 mPas.
- Material:
- Stainless steel
Flow Meter
FMT 120 PP/GF | PTFE
Turbine-type meter, G 1 intake connecting thread, made from polypropylene
- Material:
- Polypropylene
Flow Meter
FMT 120 PP/GF | PTFE
Turbine-type meter, G 1 ¼ intake connecting thread, made from polypropylene
- Material:
- Polypropylene
Flow Meter
FLUXTRONIC® evaluation electronics
no control cable, for FMC, FMO 104, FMO 110 as well as VISCOPOWER F 580 with motor flange and integrated pulse generator
View product
Drum and container pumps
F 430 PP-50/38 | FKM
with mechanical seal, for pumping out of drums. Made from polypropylene, FKM seal, 50 mm diameter.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PP-40/33 Z | FKM
with mechanical seal, for pumping out of drums. Made from polypropylene, FKM seal, semi-axial rotor.
- Max. flow rate:
- 100 l/min
- Max. discharge head:
- 24 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PP-40/33 | EPDM
with mechanical seal, for pumping out of drums. Made from polypropylene, EPDM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PP-100/50 | FKM
with mechanical seal for pumping out of open drums. Made from polypropylene, with impeller.
- Max. flow rate:
- 110 l/min
- Max. discharge head:
- 32 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PVDF-40/33 | FKM
with mechanical seal, for pumping out of drums. Made from polyvinylidene fluoride, FKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 424 PP-50/38 | FKM
sealless, for pumping out of drums. Made from polypropylene, FKM seal, 50 mm diameter.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PVDF-50/43 Z | FKM
with mechanical seal, for pumping out of drums. Made from polyvinylidene fluoride, FKM seal, semi-axial rotor.
- Max. flow rate:
- 110 l/min
- Max. discharge head:
- 30 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 424 PP-50/43 Z | FKM
sealless, for pumping out of drums. Made from polypropylene, FKM seal, semi-axial rotor.
- Max. flow rate:
- 125 l/min
- Max. discharge head:
- 30 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PVDF-50/38 | FKM
with mechanical seal, for pumping out of drums. Made from polyvinylidene fluoride, FKM seal, 50 mm diameter.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 430 PVDF-40/33 Z | FKM
with mechanical seal, for pumping out of drums. Made from polyvinylidene fluoride, FKM seal, semi-axial rotor.
- Max. flow rate:
- 100 l/min
- Max. discharge head:
- 24 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 424 PP-41/36 | EPDM
sealless, for pumping the same media every time. Made from polypropylene, shaft made from Hastelloy C.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Drum and container pumps
F 430 PVDF-40/33 | FFKM
with mechanical seal, for pumping out of canisters. Made from polyvinylidene fluoride, FFKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 424 PVDF-41/36 | FKM
sealless, for pumping out of drums. Made from polyvinylidene fluoride, FKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 310 PP-32/25 | FKM
with permanently fitted motor, for pumping out of drums, made from polypropylene, with mechanical seal, FKM seal.
- Motor type:
- F 310
- Max. flow rate:
- 48 l/min
- Max. discharge head:
- 6.9 mWk
- Rated output:
- 0.23 kW
Drum and container pumps
F 424 PP/S-41/35 Z | FKM
sealless, for pumping AdBlue® out of IBCs. Made from polypropylene, FKM seal, semi-axial rotor
- Max. flow rate:
- 100 l/min
- Max. discharge head:
- 24 mWk
- Material:
- Polypropylene
Drum and container pumps
F 424 PVDF-41/36 | FFKM
sealless, for pumping out of drums. Made from polyvinylidene fluoride, FFKM seal.
- Max. flow rate:
- 205 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polyvinylidene fluoride
Drum and container pumps
F 426 PP-50/33 | FKM
for mixing and/or pumping out of drums. Made from polypropylene, FKM seal.
- Max. flow rate:
- 240 l/min
- Max. discharge head:
- 13 mWk
- Material:
- Polypropylene
Compare the suitable pumps
Click a column heading to sort.
| Pump | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| F 430 AL-41/38 | F 430 | Aluminium | NBR | 65 l/min | 9.5 mWk | 600 mPas | 1,000 mm | No | no |
| F 424 PP/S-41/35Z | F 424 | Polypropylene | FKM | – | – | – | 1,200 mm | – | – |
| F 424 PP/S-41/35Z | F 424 | Polypropylene | FKM | 50 l/min | 18 mWk | 800 mPas | 1,200 mm | No | – |
| F 430 PVDF-40/33 | F 430 | Polyvinylidene fluoride | FKM | 40 l/min | 9.5 mWk | 600 mPas | 1,000 mm | No | no |
| FP 314 PP/S-32/25 | FP 314 | Polypropylene | FKM | 33 l/min | 6.5 mWk | 250 mPas | – | No | no |
| F 314 PP/S-32/25 | F 314 | Polypropylene | FKM | 36 l/min | 6.7 mWk | 250 mPas | – | No | no |
| F 430 AL-41/38 | NBR | F 430 | Aluminium | NBR | 240 l/min | 13 mWk | 1,000 mPas | 1,000 mm | No | no |
| F 430 AL-50/38 | NBR | F 430 | Aluminium | NBR | 240 l/min | 13 mWk | 1,000 mPas | 1,000 mm | No | no |
| F 430 AL-41/37 Z | NBR | F 430 | Aluminium | NBR | 240 l/min | 30 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PP-40/33 TR | FKM | F 430 | Polypropylene | FKM | 205 l/min | 13 mWk | 1,200 mPas | – | No | no |
| F 424 PP-41/36 | FKM | F 424 | Polypropylene | FKM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PP-40/33 | FKM | F 430 | Polypropylene | FKM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 424 PP-41/35 Z | FKM | F 424 | Polypropylene | FKM | 100 l/min | 24 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PP-50/43 Z | FKM | F 430 | Polypropylene | FKM | 110 l/min | 30 mWk | 1,200 mPas | 1,000 mm | No | no |
| FMC 100/S/PPS/2/A | FKM | – | Stainless steel | FEP with FKM core | – | – | 2,500 mPas | – | Yes | no |
| FMO 110/S/S/1 | – | Stainless steel | FKM | – | – | 1,000 mPas | – | Yes | EC 1935/2004 |
| FMT 120 PP/GF | PTFE | – | Polypropylene | PTFE | – | – | 40 mPas | – | No | no |
| FMT 120 PP/GF | PTFE | – | Polypropylene | PTFE | – | – | 40 mPas | – | No | no |
| FLUXTRONIC® evaluation electronics | – | – | – | – | – | – | – | – | – |
| F 430 PP-50/38 | FKM | F 430 | Polypropylene | FKM | 240 l/min | 13 mWk | 1,000 mPas | 1,000 mm | No | no |
| F 430 PP-40/33 Z | FKM | F 430 | Polypropylene | FKM | 100 l/min | 24 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PP-40/33 | EPDM | F 430 | Polypropylene | EPDM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PP-100/50 | FKM | F 430 | Polypropylene | FKM | 110 l/min | 32 mWk | 150 mPas | 1,000 mm | No | no |
| F 430 PVDF-40/33 | FKM | F 430 | Polyvinylidene fluoride | FKM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 424 PP-50/38 | FKM | F 424 | Polypropylene | FKM | 240 l/min | 13 mWk | 1,000 mPas | 1,000 mm | No | no |
| F 430 PVDF-50/43 Z | FKM | F 430 | Polyvinylidene fluoride | FKM | 110 l/min | 30 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 424 PP-50/43 Z | FKM | F 424 | Polypropylene | FKM | 125 l/min | 30 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PVDF-50/38 | FKM | F 430 | Polyvinylidene fluoride | FKM | 240 l/min | 13 mWk | 1,000 mPas | 1,000 mm | No | no |
| F 430 PVDF-40/33 Z | FKM | F 430 | Polyvinylidene fluoride | FKM | 100 l/min | 24 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 424 PP-41/36 | EPDM | F 424 | Polypropylene | EPDM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 430 PVDF-40/33 | FFKM | F 430 | Polyvinylidene fluoride | FFKM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 424 PVDF-41/36 | FKM | F 424 | Polyvinylidene fluoride | FKM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 310 PP-32/25 | FKM | F 310 | Polypropylene, polyamide | FKM | 48 l/min | 6.9 mWk | 250 mPas | 1,000 mm | No | – |
| F 424 PP/S-41/35 Z | FKM | F 424 | Polypropylene | FKM | 100 l/min | 24 mWk | 1,200 mPas | 1,200 mm | No | no |
| F 424 PVDF-41/36 | FFKM | F 424 | Polyvinylidene fluoride | FFKM | 205 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
| F 426 PP-50/33 | FKM | F 426 | Polypropylene | FKM | 240 l/min | 13 mWk | 1,200 mPas | 1,000 mm | No | no |
Suitability applies at the stated concentration and temperature. Unsure about your application? Our specialists are happy to advise.